Digital Multimeter TRUE RMS LCD 60000 (YT-730896)

This advanced measuring device is designed for accurate diagnostics of electrical installations, electronic circuits, and industrial devices. Counting up to 60000 digits allows for precise readings even of small changes in parameters, while a wide range of functions enables both basic and advanced measurements of electrical quantities.

The large multifunctional LCD display with the ability to simultaneously display two measured values, automatic screen backlight, and illuminated measurement sockets significantly improve work comfort in challenging lighting conditions. A range of functions that simplify measurements, along with a wide measurement range, speed of operation, and industrial accuracy will be appreciated by both electronics specialists and electricians, as well as DIY enthusiasts. The sturdy casing with a non-slip protective PVC cover enhances safety during use and protects the device from slipping out of hands and mechanical damage, while silicone-insulated measuring wires provide high strength and resistance to elevated temperatures.

• AC voltage: A.C. 0-750 V, TRUE RMS (40-1000 Hz)
• DC voltage: D.C. 0-1000 V
• AC current: A.C. 0-10 A, TRUE RMS (40-1000 Hz)
• DC current: D.C. 0-10 A
• Resistance: 0-60 MΩ
• Diode test: IF 1.8 mA, UR 3.2 V
• Continuity test: 0-50 Ω

• Capacitance: 0-60 mF
• Frequency: 0-25 MHz
• Temperature: -20 to 1000°C
• Non-contact AC voltage detection: NCV
• Peak voltage measurement: PEAK VALUE

An example of accuracy determination for AC voltage measurement. Calculations for the measurement result: 235 V.

The accuracy of the YT-730896 meter for this range is: ±(0.8% + 10), resolution 0.01 V. Measurement error calculation formula: (measurement result x 0.8%) + 10 x resolution. Calculations: (235 x 0.8%) + 10 x 0.01 = 1.88 + 0.1 = 1.98 V. The actual result considering the measurement error for a reading of 235 V = 235 ± 1.98 V.

The result considering the measurement error for a reading of DC voltage: 12 V = 12 ± 0.011 V. The result considering the measurement error for a reading of AC current: 8 A = 8 ± 0.17 A. A table with resolution and accuracy for this measurement can be found in the user manual.

• TRUE RMS - the meter displays the true effective value of AC voltage/current; unlike averaging meters, devices with TRUE RMS show the correct value not only for sinusoidal signals but also for distorted sinusoidal signals.
• NCV - non-contact detection of AC voltage using induction; the meter detects the presence of voltage in an insulated wire using the NCV sensor on the front panel of the device.
• AUTO - automatic range setting; activated by default.
• RANGE - manual range adjustment, useful when checking many identical components.
• REL - function to zero the display and take the visible value as the reference level.
• FUNC - change measurement mode, for example, from AC voltage measurement to DC.
• MAX/MIN - save the maximum or minimum value from the current measurement.
• PEAK - peak value for AC current and voltage measurements.
• HOLD - hold the current measured value on the display.

• LCD display, maximum displayed result: 60000.
• Screen backlight with light sensor.
• Measurement sockets are illuminated after selecting the measurement.
• Audible and visual signal in the continuity test for resistance below 50 Ω.
• Ability to turn on diode and continuity tests separately.
• Measuring probes 13 cm long.
• Wire length including probes: 130 cm.
• Wire diameter including insulation: 3.5 mm.
• Point probe for temperature measurement.
• Design with overload protection.
• ABS plastic housing.
• Automatic shutdown after 15 minutes of inactivity.
• Low battery indicator.
• Soft zippered case.
• Power supply: 3 batteries 1.5 V (AAA).